Description | Description:
Easy and efficient pressure test of the cylinder head and cylinder block coolant circuits.
Quick and easy clamping system allowing tests at a pressure of 4 to 5 bar.
Features:
- 360° Electric powered roll-over fixture.
- Hydraulic cradle lift for easy positioning of heavy cylinder heads.
- Stainless steel tank with heat barrier.
- Heating elements: two changeover 4500 Watts elements.
- Water level control.
- Electronic adjustable thermostat.
- Heating programmer: daily or weekly.
| Description
TAB-ECP63 electric press is a suitable open type of crank press featuring a left and right open type machine body (i.e., a C-shaped machine body). Its steel plate welded body has a high shock-absorbing performance. Its novel overall design gives the machine an elegant appearance. Its throat has a certain depth. The compact structure makes the use convenient and operation safe. The punch press is equipped with a turn-key rigid clutch, a cam band brake, and a press-down type safety device. Its working table is open on three sides, so the mold loading and unloading, and operation are convenient. The punch press is widely used because it provides good conditions for mechanization and automation. And as the main equipment for plate punching production, the punch press can be used for punching holes, blanking, trimming, bending, shallow stretching, and forming. | Description
TAB-ECP40 eccentric press is a suitable open type of crank press featuring a left and right open type machine body (i.e., a C-shaped machine body). Its steel plate welded body has a high shock-absorbing performance. Its novel overall design gives the machine an elegant appearance. Its throat has a certain depth. The compact structure makes the use convenient and operation safe. The punch press is equipped with a turn-key rigid clutch, a cam band brake, and a press-down type safety device. Its working table is open on three sides, so the mold loading and unloading, and operation are convenient. The punch press is widely used because it provides good conditions for mechanization and automation. And as the main equipment for plate punching production, the punch press can be used for punching holes, blanking, trimming, bending, shallow stretching, and forming. | Description
This SP3103 machine is a step-less timing vertical drilling machine with a wide belt, light in weight small in volume easy to operate, safe, and reliable.
It is a universal machine that could be widely used for small and middle-sized workpieces or drilling spot facing, reaming, tapping, etc.
And it also could equip many kinds of accessories, to extend machining function and usage area.
Digital speeds screen installed
These machines are suitable for machining workshops, maintenance workshops, and mini-type workshops. | Descriptions
Round bending machine both Vertical and horizontal bending
Features:
- Horizontal and vertical operation
- With standard foot pedal
- Special cast frame+
- Shafts are hardened with special steel material
- Rollers are special steel material hardened and grounded
- Gears Milled with full material
| Description
TAB-ECP80 eccentric press is a suitable open type of crank press featuring a left and right open type machine body (i.e., a C-shaped machine body). Its steel plate welded body has a high shock-absorbing performance. Its novel overall design gives the machine an elegant appearance. Its throat has a certain depth. The compact structure makes the use convenient and operation safe. The punch press is equipped with a turn-key rigid clutch, a cam band brake, and a press-down type safety device. Its working table is open on three sides, so the mold loading and unloading, and operation are convenient. The punch press is widely used because it provides good conditions for mechanization and automation. And as the main equipment for plate punching production, the punch press can be used for punching holes, blanking, trimming, bending, shallow stretching, and forming. |
Content |
Model |
TPT 1600 |
TPT 1600L |
Maximum length (mm) |
1300 mm |
1350 mm |
Maximum width (mm) |
400 mm |
425 mm |
Maximum height (mm) |
300 mm |
300 mm |
Capacity of stainless-steel tank |
500liters |
550liters |
Heating elements (kW) |
2x4.5 kW |
2x4.5 kW |
Hydraulic hoist (kW) |
0.55 kW |
0.55 kW |
Gear-motor (kW) |
0.25 kW |
0.25 kW |
Rotational speed (tr/min) |
4 tr/min |
4 tr/min |
Up and down travel time (mm in 10sec) |
600mm |
600mm |
Thermostat (°C ) |
14-70 °C |
14-70 °C |
Power supply |
3 PHASE 380V-AC-60Hz |
3PHASE 380V-AC-60Hz |
Net weight approx. (kg) |
400 |
480 |
Overall dimension: |
Length(mm) |
2000 mm |
2100 mm |
Width (mm) |
1050 mm |
1050 mm |
Height (mm) |
1700 mm |
1700 mm |
|
Model |
Unit |
TAB-ECP63 |
Nominal Pressure |
kn |
630 |
Travel of slip block |
mm |
100 |
Frequency of travel |
Frequency/minute |
50 |
Enclosed height |
mm |
70 |
Maximum adjustment of enclosed height |
mm |
80 |
Distance from center of slip block to press body |
mm |
230 |
Size of shank holes diameter |
mm |
50 |
Bolster Surface |
Front to Rear |
mm |
450 |
Left to Right |
mm |
700 |
Size of shank holes depth |
mm |
70 |
Distance between columns |
mm |
370 |
Mold Height |
mm |
220 |
Motor Power |
kw |
5.5 |
Overall Dimensions |
F.R. |
mm |
1800 |
L.R. |
mm |
1500 |
Height |
mm |
2650 |
|
Model |
Unit |
TAB-ECP40 |
Nominal Pressure |
kn |
400 |
Travel of slip block |
mm |
100 |
Frequency of travel |
Frequency/minute |
50 |
Enclosed height |
mm |
70 |
Maximum adjustment of enclosed height |
mm |
60 |
Distance from center of slip block to press body |
mm |
230 |
Size of shank holes diameter |
mm |
50 |
Bolster Surface |
Front to Rear |
mm |
410 |
Left to Right |
mm |
640 |
Size of shank holes depth |
mm |
70 |
Distance between columns |
mm |
320 |
Thickness of plate of workbench |
mm |
80 |
Mold Height |
mm |
230 |
Maximum tilt angle of press body |
degree |
15 |
Motor Power |
kw |
3 |
Overall Dimension |
F.B. |
mm |
1400 |
L.R. |
mm |
1200 |
Height |
mm |
2450 |
|
model |
SP3103 |
Max. drilling diameter (steel) |
25mm |
Max. taping diameter (steel) |
M12mm |
Max. stroke of the spindle |
110mm |
Distance between spindle center line to the generating line of column |
230mm |
Max. distance between spindle end to the surface of the worktable |
690mm |
Max. distance between spindle end to the worktable surface of the base |
1180mm |
Max. stroke of worktable and its bracket |
555mm |
Spindle taper bore |
MT3 |
Number of speed steps of the spindle |
Stepless |
Spindle speed range |
80~1600 r/min |
Working area of the worktable (L x W) |
400×320mm |
Working area of the worktable of the base (L x W) |
340×320mm |
Diameter of column |
100mm |
Power of the main power |
0.55/0.85kw |
Machine dimension (L×B×H) |
820×530×1715mm |
Packing dimension(L×B×H) |
860×580×1800mm |
Net weight/gross weight |
245/280kg |
|
model |
Pipe Bending Machine RBM30HV |
Motor power |
1.1 kW |
Leading roller speed |
9 r/min |
Roller shaft diameter |
30 mm |
Dimensions machine |
820×620×1260 mm |
Net weight |
282 kg |
|
Model |
Unit |
TAB-ECP80 |
Nominal Pressure |
kn |
800 |
Travel of slip block |
mm |
120 |
Frequency of travel |
Frequency/minute |
40 |
Enclosed height |
mm |
70 |
Maximum adjustment of enclosed height |
mm |
60 |
Distance from center of slip block to press body |
mm |
90 |
Size of shank holes diameter |
mm |
60 |
Bolster Surface |
Front to Rear |
mm |
480 |
Left to Right |
mm |
750 |
Size of shank holes depth |
mm |
70 |
Distance between columns |
mm |
300 |
Mold Height |
mm |
250 |
Motor Power |
kw |
5.5 |
Overall Dimensions |
F.R. |
mm |
1790 |
L.R. |
mm |
1420 |
Height |
mm |
2550 |
|